=> run setargs_mmc => run boot_dsp0 dsp0:gpio init config fail DSP0 start ok, img length 252960, booting from 0x400660 => run boot_normal Android's image name: d1-nezha No reserved memory region found in source FDT [45.931] Starting kernel ... [ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000 [ 0.000000] Linux version 5.4.61 (wuhuabin@AwExdroid86) (riscv64-unknown-linux-gnu-gcc (C-SKY RISCV Tools V1.8.4 B20200702) 8.1.0, GNU ld (GNU Binutils) 2.32) #51 PREEMPT Mon May 10 12:41:05 UTC 2021 [ 0.000000] cma: Reserved 8 MiB at 0x00000000bf800000 [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000040200000-0x00000000bfffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040200000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x00000000bfffffff] [ 0.000000] On node 0 totalpages: 523776 [ 0.000000] DMA32 zone: 7161 pages used for memmap [ 0.000000] DMA32 zone: 0 pages reserved [ 0.000000] DMA32 zone: 523776 pages, LIFO batch:63 [ 0.000000] elf_hwcap is 0x20112d [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516615 [ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p5 rootwait init=/sbin/init partitions=mbr@ubi0_0:boot-resource@ubi0_1:env@ubi0_2:env-redund@ubi0_3:boot@ubi0_4:rootfs@ubi0_5:dsp0@ubi0_6:recovery@ubi0_7:UDISK@ubi0_8: cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.hardware=sun20iw1p1 boot_type=5 androidboot.boot_type=5 gpt=1 uboot_message=2018.05-00107-gc22c3d075c(04/24/2021-07:52:58) mbr_offset=1556480 disp_reserve [ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Sorting __ex_table... [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 2040724K/2095104K available (5944K kernel code, 655K rwdata, 2062K rodata, 208K init, 251K bss, 46188K reserved, 8192K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0 [ 0.000000] plic: mapped 200 interrupts with 1 handlers for 2 contexts. [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [0] [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000005] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000023] riscv_timer_clockevent depends on broadcast, but no broadcast function available [ 0.000329] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000923] Console: colour dummy device 80x25 [ 0.000963] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.000979] pid_max: default: 32768 minimum: 301 [ 0.001189] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.001227] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.002950] ASID allocator initialised with 65536 entries [ 0.003113] rcu: Hierarchical SRCU implementation. [ 0.003906] devtmpfs: initialized [ 0.015806] random: get_random_u32 called from bucket_table_alloc.isra.31+0x4e/0x15e with crng_init=0 [ 0.016707] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.016737] futex hash table entries: 256 (order: 0, 6144 bytes, linear) [ 0.017165] pinctrl core: initialized pinctrl subsystem [ 0.018487] NET: Registered protocol family 16 [ 0.020441] DMA: preallocated 256 KiB pool for atomic allocations [ 0.021067] cpuidle: using governor menu [ 0.066098] rtc_ccu: sunxi ccu init OK [ 0.072542] clock: sunxi ccu init OK [ 0.073476] clock: sunxi ccu init OK [ 0.112323] iommu: Default domain type: Translated [ 0.112494] sunxi iommu: irq = 4 [ 0.113653] SCSI subsystem initialized [ 0.113992] usbcore: registered new interface driver usbfs [ 0.114093] usbcore: registered new interface driver hub [ 0.114196] usbcore: registered new device driver usb [ 0.114376] mc: Linux media interface: v0.10 [ 0.114437] videodev: Linux video capture interface: v2.00 [ 0.115395] Advanced Linux Sound Architecture Driver Initialized. [ 0.115984] Bluetooth: Core ver 2.22 [ 0.116064] NET: Registered protocol family 31 [ 0.116075] Bluetooth: HCI device and connection manager initialized [ 0.116094] Bluetooth: HCI socket layer initialized [ 0.116107] Bluetooth: L2CAP socket layer initialized [ 0.116142] Bluetooth: SCO socket layer initialized [ 0.116421] pwm module init! [ 0.117951] g2d 5410000.g2d: Adding to iommu group 0 [ 0.118436] G2D: rcq version initialized.major:250 [ 0.118981] input: sunxi-keyboard as /devices/virtual/input/input0 [ 0.120593] clocksource: Switched to clocksource riscv_clocksource [ 0.132271] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver [ 0.147914] NET: Registered protocol family 2 [ 0.148685] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) [ 0.148784] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.148980] TCP bind hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.149136] TCP: Hash tables configured (established 16384 bind 16384) [ 0.149321] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.149424] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.149743] NET: Registered protocol family 1 [ 0.151079] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator [ 0.151648] spi spi0: spi0 supply spi not found, using dummy regulator [ 0.151913] sunxi_spi_resource_get()2062 - [spi0] SPI MASTER MODE [ 0.152023] sunxi_spi_clk_init()2138 - [spi0] mclk 100000000 [ 0.152695] sunxi_spi_probe()2542 - [spi0]: driver probe succeed, base ffffffd00405a000, irq 31 [ 0.154570] Initialise system trusted keyrings [ 0.154823] workingset: timestamp_bits=62 max_order=19 bucket_order=0 [ 0.162397] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.181986] Key type asymmetric registered [ 0.182001] Asymmetric key parser 'x509' registered [ 0.182025] io scheduler mq-deadline registered [ 0.182034] io scheduler kyber registered [ 0.182053] atomic64_test: passed [ 0.183241] [DISP]disp_module_init [ 0.183801] disp 5000000.disp: Adding to iommu group 0 [ 0.184408] [DISP] disp_init,line:2385: [ 0.184414] smooth display screen:0 type:1 mode:4 [ 0.220850] display_fb_request,fb_id:0 [ 0.250642] disp_al_manager_apply ouput_type:1 [ 0.250808] [DISP] lcd_clk_config,line:731: [ 0.250820] disp 0, clk: pll(420000000),clk(420000000),dclk(70000000) dsi_rate(70000000) [ 0.250820] clk real:pll(420000000),clk(420000000),dclk(105000000) dsi_rate(150000000) [ 0.251217] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator [ 0.251963] [DISP]disp_module_init finish [ 0.252873] sunxi_sid_init()497 - insmod ok [ 0.253426] pwm-regulator: supplied by regulator-dummy [ 0.260707] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator [ 0.261154] uart uart0: get regulator failed [ 0.261185] uart uart0: uart0 supply uart not found, using dummy regulator [ 0.261507] uart0: ttyS0 at MMIO 0x2500000 (irq = 18, base_baud = 1500000) is a SUNXI [ 0.261534] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n [ 1.049933] printk: console [ttyS0] enabled [ 1.055587] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator [ 1.067005] uart uart1: get regulator failed [ 1.071879] uart uart1: uart1 supply uart not found, using dummy regulator [ 1.079908] uart1: ttyS1 at MMIO 0x2500400 (irq = 19, base_baud = 1500000) is a SUNXI [ 1.089849] misc dump reg init [ 1.093912] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9 [ 1.101153] sunxi-rfkill soc@3000000:rfkill@0: devm_pinctrl_get() failed! [ 1.108764] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed [ 1.116087] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed [ 1.123542] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1) [ 1.130050] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power. [ 1.137021] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1) [ 1.144748] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1 [ 1.152607] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1 [ 1.160778] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled [ 1.168393] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power. [ 1.175203] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1) [ 1.182738] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=210 assert=0 [ 1.191046] [ADDR_MGT] addr_mgt_probe: module version: v1.0.8 [ 1.198566] [ADDR_MGT] addr_mgt_probe: success. [ 1.204686] sunxi-spinand: AW SPINand MTD Layer Version: 2.0 20201228 [ 1.211921] sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.10 20200306 [ 1.219813] sunxi-spinand-phy: not detect any munufacture from id table [ 1.227263] sunxi-spinand-phy: get spi-nand Model from fdt fail [ 1.233891] sunxi-spinand-phy: get phy info from fdt fail [ 1.239930] sunxi-spinand-phy: not detect munufacture from fdt [ 1.246634] sunxi-spinand-phy: detect munufacture from id table: Mxic [ 1.253883] sunxi-spinand-phy: detect spinand id: ff0326c2 ffffffff [ 1.260890] sunxi-spinand-phy: ========== arch info ========== [ 1.267408] sunxi-spinand-phy: Model: MX35LF2GE4AD [ 1.274126] sunxi-spinand-phy: Munufacture: Mxic [ 1.280043] sunxi-spinand-phy: DieCntPerChip: 1 [ 1.285725] sunxi-spinand-phy: BlkCntPerDie: 2048 [ 1.291668] sunxi-spinand-phy: PageCntPerBlk: 64 [ 1.297391] sunxi-spinand-phy: SectCntPerPage: 4 [ 1.303071] sunxi-spinand-phy: OobSizePerPage: 64 [ 1.308795] sunxi-spinand-phy: BadBlockFlag: 0x1 [ 1.314638] sunxi-spinand-phy: OperationOpt: 0x7 [ 1.320477] sunxi-spinand-phy: MaxEraseTimes: 65000 [ 1.326517] sunxi-spinand-phy: EccFlag: 0x2 [ 1.332391] sunxi-spinand-phy: EccType: 8 [ 1.338018] sunxi-spinand-phy: EccProtectedType: 3 [ 1.343668] sunxi-spinand-phy: ======================================== [ 1.351090] sunxi-spinand-phy: [ 1.354587] sunxi-spinand-phy: ========== physical info ========== [ 1.361497] sunxi-spinand-phy: TotalSize: 256 M [ 1.366851] sunxi-spinand-phy: SectorSize: 512 B [ 1.372214] sunxi-spinand-phy: PageSize: 2 K [ 1.377357] sunxi-spinand-phy: BlockSize: 128 K [ 1.382746] sunxi-spinand-phy: OOBSize: 64 B [ 1.387986] sunxi-spinand-phy: ======================================== [ 1.395376] sunxi-spinand-phy: [ 1.398889] sunxi-spinand-phy: ========== logical info ========== [ 1.405702] sunxi-spinand-phy: TotalSize: 256 M [ 1.411060] sunxi-spinand-phy: SectorSize: 512 B [ 1.416413] sunxi-spinand-phy: PageSize: 4 K [ 1.421580] sunxi-spinand-phy: BlockSize: 256 K [ 1.426917] sunxi-spinand-phy: OOBSize: 128 B [ 1.432302] sunxi-spinand-phy: ======================================== [ 1.439801] sunxi-spinand-phy: block lock register: 0x00 [ 1.445958] sunxi-spinand-phy: feature register: 0x11 [ 1.451622] sunxi-spinand-phy: sunxi physic nand init end [ 1.458265] Creating 4 MTD partitions on "sunxi_mtd_nand": [ 1.464519] 0x000000000000-0x000000100000 : "boot0" [ 1.481829] 0x000000100000-0x000000500000 : "uboot" [ 1.487980] random: fast init done [ 1.521758] 0x000000500000-0x000000600000 : "secure_storage" [ 1.541776] 0x000000600000-0x000010000000 : "sys" [ 1.935015] random: crng init done [ 2.692282] libphy: Fixed MDIO Bus: probed [ 2.696886] CAN device driver interface [ 2.702741] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator [ 2.714104] sunxi gmac driver's version: 1.0.0 [ 2.719201] gmac-power0: NULL [ 2.722556] gmac-power1: NULL [ 2.725853] gmac-power2: NULL [ 2.730310] Failed to alloc md5 [ 2.733909] eth0: Use random mac address [ 2.738645] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.746063] sunxi-ehci: EHCI SUNXI driver [ 2.751193] get ehci1-controller wakeup-source is fail. [ 2.757121] sunxi ehci1-controller don't init wakeup source [ 2.763469] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xffffffe0008d6748, 0x:ffffffd004079000, irq_no:31 [ 2.777031] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply drvvbus not found, using dummy regulator [ 2.789651] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller [ 2.796966] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1 [ 2.806793] sunxi-ehci 4200000.ehci1-controller: irq 49, io mem 0x04200000 [ 2.840643] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00 [ 2.848435] sunxi-ehci 4200000.ehci1-controller: ehci_irq: highspeed device connect [ 2.857952] hub 1-0:1.0: USB hub found [ 2.862307] hub 1-0:1.0: 1 port detected [ 2.867490] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.874486] sunxi-ohci: OHCI SUNXI driver [ 2.879560] get ohci1-controller wakeup-source is fail. [ 2.885573] sunxi ohci1-controller don't init wakeup source [ 2.891874] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xffffffe0008d7288 [ 2.902309] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply drvvbus not found, using dummy regulator [ 2.914857] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller [ 2.922130] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2 [ 2.931976] sunxi-ohci 4200400.ohci1-controller: irq 50, io mem 0x04200400 [ 3.005600] hub 2-0:1.0: USB hub found [ 3.009836] hub 2-0:1.0: 1 port detected [ 3.015325] usbcore: registered new interface driver uas [ 3.021532] usbcore: registered new interface driver usb-storage [ 3.028308] usbcore: registered new interface driver ums-alauda [ 3.035058] usbcore: registered new interface driver ums-cypress [ 3.041921] usbcore: registered new interface driver ums-datafab [ 3.048685] usbcore: registered new interface driver ums_eneub6250 [ 3.055735] usbcore: registered new interface driver ums-freecom [ 3.062538] usbcore: registered new interface driver ums-isd200 [ 3.069197] usbcore: registered new interface driver ums-jumpshot [ 3.076148] usbcore: registered new interface driver ums-karma [ 3.082929] usbcore: registered new interface driver ums-onetouch [ 3.089874] usbcore: registered new interface driver ums-realtek [ 3.096714] usbcore: registered new interface driver ums-sddr09 [ 3.103478] usbcore: registered new interface driver ums-sddr55 [ 3.110137] usbcore: registered new interface driver ums-usbat [ 3.117874] sunxi_gpadc_init,1968, success [ 3.124740] sunxi-rtc 7090000.rtc: registered as rtc0 [ 3.130492] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:02:40 UTC (160) [ 3.139654] sunxi-rtc 7090000.rtc: sunxi rtc probed [ 3.145550] i2c /dev entries driver [ 3.149536] IR NEC protocol handler initialized [ 3.155366] sunxi cedar version 1.1 [ 3.159526] sunxi-cedar 1c0e000.ve: Adding to iommu group 0 [ 3.165918] VE: install start!!! [ 3.165918] [ 3.171501] VE: cedar-ve the get irq is 6 [ 3.171501] [ 3.177809] VE: ve_debug_proc_info:00000000df48d120, data:0000000096f1d507, lock:00000000c5e3dfff [ 3.177809] [ 3.189436] VE: install end!!! [ 3.189436] [ 3.195376] sunxi-wdt 6011000.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 3.204584] Bluetooth: HCI UART driver ver 2.3 [ 3.209541] Bluetooth: HCI UART protocol H4 registered [ 3.215308] Bluetooth: HCI UART protocol BCSP registered [ 3.221301] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10 [ 3.228567] [XR_BT_LPM] bluesleep_probe: bt_wake polarity: 1 [ 3.234990] usb 1-1: new high-speed USB device number 2 using sunxi-ehci [ 3.242567] [XR_BT_LPM] bluesleep_probe: host_wake polarity: 1 [ 3.249123] [XR_BT_LPM] bluesleep_probe: wakeup source is disabled! [ 3.249123] [ 3.257859] [XR_BT_LPM] bluesleep_probe: uart_index(1) [ 3.267739] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.19 2021-03-24 19:50) [ 3.277736] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8 [ 3.284015] sunxi-mmc 4020000.sdmmc: No vmmc regulator found [ 3.290346] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found [ 3.296779] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found [ 3.303247] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found [ 3.309752] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found [ 3.316313] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found [ 3.322842] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found [ 3.329829] sunxi-mmc 4020000.sdmmc: Got CD GPIO [ 3.335349] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail [ 3.342144] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.353333] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator [ 3.373494] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.397916] sunxi-mmc 4020000.sdmmc: detmode:gpio irq [ 3.403653] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.416095] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.19 2021-03-24 19:50) [ 3.426172] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8 [ 3.432500] sunxi-mmc 4021000.sdmmc: No vmmc regulator found [ 3.438867] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found [ 3.445356] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.456944] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found [ 3.463470] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found [ 3.470182] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found [ 3.476872] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found [ 3.483550] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found [ 3.490184] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed [ 3.498952] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.511745] hub 1-1:1.0: USB hub found [ 3.516379] hub 1-1:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.525443] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.536592] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.548266] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 3.568491] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.588372] mmc0: host does not support reading read-only switch, assuming write-enable [ 3.597385] sunxi-mmc 4021000.sdmmc: detmode:manually by software [ 3.605092] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 3.612018] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 3.623477] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 3.630351] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.642123] sunxi_led_probe()1715 - start [ 3.646624] sunxi_get_str_of_property()1560 - failed to get the string of propname led_regulator! [ 3.656702] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 3.668403] sunxi_register_led_classdev()1448 - led_classdev start [ 3.675615] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 3.689031] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.703652] sunxi_led_probe()1820 - finish [ 3.708848] usbcore: registered new interface driver usbhid [ 3.715288] mmc0: new high speed SDHC card at address 5048 [ 3.721513] usbhid: USB HID core driver [ 3.725808] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 3.733379] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 3.740581] mmcblk0: mmc0:5048 SD32G 29.0 GiB [ 3.745600] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 3.753188] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 3.759929] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 3.772118] usbcore: registered new interface driver snd-usb-audio [ 3.785633] sunxi-daudio 2034000.daudio: regulator missing or invalid [ 3.793693] [AUDIOCODEC][sunxi_codec_parse_params][2208]:digital_vol:0, lineout_vol:26, mic1gain:31, mic2gain:31 pa_msleep:120, pa_level:1, pa_pwr_level:1 [ 3.793693] [ 3.811102] [AUDIOCODEC][sunxi_codec_parse_params][2244]:adcdrc_cfg:0, adchpf_cfg:0, dacdrc_cfg:0, dachpf:0 [ 3.822855] [AUDIOCODEC][sunxi_internal_codec_probe][2380]:codec probe finished [ 3.832311] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present! [ 3.842379] [SNDCODEC][sunxi_card_init][583]:card init finished [ 3.850243] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok [ 3.862089] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 3.870371] GPT:58720255 != 60751871 [ 3.874439] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input1 [ 3.885854] GPT:Alternate GPT header not at the end of the disk. [ 3.893251] [SNDCODEC][sunxi_card_dev_probe][832]:register card finished [ 3.900818] GPT:58720255 != 60751871 [ 3.904799] GPT: Use GNU Parted to correct GPT errors. [ 3.912455] NET: Registered protocol family 10 [ 3.918138] mmcblk0: p1 p2 p3 p4 p5 p6 [ 3.923265] Segment Routing with IPv6 [ 3.927515] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.937325] NET: Registered protocol family 17 [ 3.942389] can: controller area network core (rev 20170425 abi 9) [ 3.949419] NET: Registered protocol family 29 [ 3.954453] can: raw protocol (rev 20170425) [ 3.959213] can: broadcast manager protocol (rev 20170425 t) [ 3.965653] can: netlink gateway (rev 20190810) max_hops=1 [ 3.972112] Bluetooth: RFCOMM TTY layer initialized [ 3.977566] Bluetooth: RFCOMM socket layer initialized [ 3.983454] Bluetooth: RFCOMM ver 1.11 [ 3.988672] Loading compiled-in X.509 certificates [ 3.996440] HDMI 2.0 driver init start! [ 4.000807] boot_hdmi=false [ 4.003976] ERROR: pinctrl_get for HDMI2.0 DDC fail [ 4.011042] HDMI2.0 module init end [ 4.040763] twi twi2: twi2 supply twi not found, using dummy regulator [ 4.055944] pcf857x 2-0038: probed [ 4.066138] sunxi_i2c_probe()2262 - [i2c2] probe success [ 4.082145] debugfs: Directory '2031000.dmic' with parent 'snddmic' already present! [ 4.092469] sunxi-audio-card 2031060.sounddmic: snd-soc-dummy-dai <-> 2031000.dmic mapping ok [ 4.103342] debugfs: Directory '2034000.daudio' with parent 'sndhdmi' already present! [ 4.113957] sunxi-audio-card 20340a0.sounddaudio2: snd-soc-dummy-dai <-> 2034000.daudio mapping ok [ 4.125709] get ehci0-controller wakeup-source is fail. [ 4.131689] sunxi ehci0-controller don't init wakeup source [ 4.137910] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe0008d6388, 0x:ffffffd005422000, irq_no:2e [ 4.151479] [sunxi-ehci0]: Not init ehci0 [ 4.156449] get ohci0-controller wakeup-source is fail. [ 4.162476] sunxi ohci0-controller don't init wakeup source [ 4.168694] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe0008d6ec8 [ 4.179155] [sunxi-ohci0]: Not init ohci0 [ 4.186674] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 4.198048] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 4.205647] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 4.215376] clk: Not disabling unused clocks [ 4.220143] ALSA device list: [ 4.223587] cfg80211: failed to load regulatory.db [ 4.229006] #0: audiocodec [ 4.232313] #1: snddmic [ 4.235232] #2: sndhdmi [ 4.238158] alloc_fd: slot 0 not NULL! [ 4.256905] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null) [ 4.266088] VFS: Mounted root (ext4 filesystem) readonly on device 179:5. [ 4.283482] devtmpfs: mounted [ 4.286986] Freeing unused kernel memory: 208K [ 4.292044] This architecture does not have kernel memory protection. [ 4.299226] Run /sbin/init as init process [ 4.430671] HDMI cable is connected [ 4.885906] systemd[1]: System time before build time, advancing clock. [ 4.913387] systemd[1]: Failed to look up module alias 'autofs4': Function not implemented [ 4.928776] systemd[1]: Failed to mount tmpfs at /sys/fs/cgroup: No such file or directory [ 4.939594] systemd[1]: Failed to mount cgroup at /sys/fs/cgroup/systemd: No such file or directory [!!!!!!] Failed to mount API filesystems. [ 4.990764] systemd[1]: Freezing execution. [ 5.320837] error: invalid cea_vic code:0 [ 5.325308] [HDMI2 error]: sink do not support this mode:0 [ 34.400646] usb1-vbus: disabling